Single-phase Programmable AC Power Supply
Large color touch screen with intuitive interface, easy to operate
Turn on, turn off phase angle control, 0-359.9°
Features AC, DC, AC+DC output modes, AC+DC output mode for voltage DC offset simulation
Output frequency: 15-1200Hz, programmable slew rate setting for changing voltage and frequency
Support LIST/PULSE/STEP modes to simulate all kinds of power line disturbance conditions
High output current crest factor which is ideal for inrush current testing
Sweep function for efficiency testing and shows voltage and frequency value at max power
Multiple current range to make current measurement more accurate
Front panel USB interface supports CSV format to import waveform
OCP/OVP/OPP/OTP/reverse current protection/short circuit protection
Support three phase power output, can simulate three phase unbalanced output
Support external analog input control and TTL electrical level output
Two versions to meet the cost performance and different applications
Programmable voltage and current limit, support CC mode
Support up to 2 units in series, 4 units in parallel
Triac Dimmer function for dimming/governor simulation function
Built-in power meter function, can real-time measure 15 electrical parameters . This series AC source can measure up to 40 orders of the voltage or current harmonics
Function & Advantage
The large color touch screen provides simple and fast operation for customers, real-time update of display output data and power status, and graphical display makes it more intuitive.
This series of AC power supply can set the ON phase and OFF phase of sinusoidal output waveform, suitable for the output test of switching power supply. Set the ON angle to 90 degrees for surge current testing, the power supply will show the measured value of surge current. Users can set when start to measure the surge current and the duration of the measurement.
This series AC power supply let users set the slew rate of voltage and frequency, in such application in order to reduce the inrush current during motor or compressor startup.
This series AC power supply deliver up to 5~6 times of peak current from its RMS current, so it is suitable for testing switching power supplies and motor with high inrush current issue.
This series AC power supply can test the efficiency of switching power supply and capturing the voltage, current, power and frequency at the maximum power operating point, the measurements will be displayed at the end of the sweep.
This series AC power supply built-in triac dimmer function, which is used to do dimming and speed regulating test for lamp or electric motor to ensure the products work well both in R&D and production testing.
This series AC power supply provides powerful function to simulate all kinds of power line disturbance conditions such as cycle dropout, transient spike, brown out and etc. This feature make this series AC power supply ideal for R&D labs, universities and certification labs.
Voltage Sags/Voltage Spikes
The test mode compares measurement values against a user defined set of measurement limits and shows a PASS or FAIL result in one or more measurement are out of range. The user can set when start of the measurement and duration of the test.
The user can save the screenshot via the USB interface in the front panel. The user can import a CSV file via the USB interface to generate waveform output.
This series AC power source can be used in parallel or series to provide more power, the maximum current up to 184A and the voltage up to 600V. In 3-phase mode, the Master unit is always phase A, Slave 1 is always phase B and Slave 2 is always phase C. The phase difference between phase A and B is always 120°and between phase A and C is always 240°. The output voltage of phase B and C will be set to the same setting as that for phase A (Master) if the Voltage Mode is set to COM. Or if the Voltage Mode is set to Multi, phase B and C output voltage can be set individually to simulate 3-phase unbalance system. The output of 3-Phase system can be connected for three-phase, four wire (Delta configuration) loads or for three-phase, five wire (Wye configuration) according to the application requirement.
By selecting Analog I/O card to achieve below function: Amplifier Mode In Amplfier mode, the power source acts as a power amplfier, taking a low-level analog signal and amplifying it by a fixed amount of gain.
The low output impedance and low voltage harmonics of this series power supply make it ideal for IEC61000-3-2 standard testing. A current feedback control circuit makes the output voltage changed with load. This feature is suitable for IEC61000-3-3 Flicker tests. The user can set the resistance and inductance value according to the test requirement.
Support creating waveforms made up of a series of harmonics frequencies, amplitudes and phase shifts, up to 40 orders harmonics of 50Hz or 60Hz. The harmonics measurement function measures total harmonic distortion (THD), DC voltage and current and fundamental voltage and current for output settings of 50Hz or 60Hz.The measurement of 2~40 orders can be displayed in absolute values or in percent of the fundamental, the harmonics measurement will be displayed with a graphical representation.
Options & Accessories
Input protective cover (standard)With fixing screws
Handles (standard)With fixing screws
Input protective cover (standard)With fixing screws
Output protective cover (standard)With fixing screws
RS-232 communication cable (standard)For RS-232 communication
USB communication cable (optional)For USB communication
Three-pin plug power cord (standard)10A, standard for 2U
Power cable (standard)1.5M, standard for 3U/4U
System bus communication cable (optional)Connect for master-slave communication
LAN & GPIB card & communication cable (optional)Applicable in 2U
External control card & cable (optional)Applicable in 2U
Parallel card & cable (optional)Applicable in 2U
GPIB card & cable (optional)Applicable in 3U/4U
LAN communication card & communication cable (optional)Optional for 3U/4U models, standard 568A-568B, this accessory must be confirmed when placing an order "
Parallel&external control&cable (optional)Applicable in 3U/4U
Three-pin plug power cord (optional)10A or 16A
Power cable (optional)1.5M
Professional version upgrade software (optional)Upgrade version from advanced to professional
|Model||Voltage||Current||Power||Standard Communication Interface||Frequency Range||Size|